PDA

View Full Version : Aero and CMT SBR Build



cjd3
5 June 2017, 20:52
http://i.imgur.com/hqqO2yG.jpg

Finally, after waiting for permission to build my first SBR, I have all my parts and permission.

The Aero Lower:
Aero Gen 2 Ambi forged lower with PDQ Ambi-Bolt release
Engraving by Ident Marking
Stamp by BATF
Old RRA National Match 2 Stage Trigger (On hand to be replaced at a later time)
V7 57 Safety Selector
Forward Controls EMR-A Standard Ambi Mag Release
Forward Controls EMR Mag Button
BAD-EPS pins
Ergo Grip
Aero or Brownell's Buffer Tube Assembly with carbine buffer
BCM QD Endplate
Magpul MOE Stock

CMT Upper:
CMT UPUR-1LH upper
CMT UHPR-6.7 MOD 1 Handguard
Ballistic Advantage 8.3" 300 Blackout BA Hanson Performance Series
Ballistic Advantage pinned Lo Pro Gas Block
Forward Controls LDFA
AXTS Raptor Charging Handle
Stag Left Handed BCG
SilencerCo ASR Muzzle Brake
SilencerCo ASR Blast Shield
Daniel Defense fixed sights

No bikes will be built tonight.

mustangfreek
5 June 2017, 21:02
Nice list.

First SBR, you must be excited..I need to join the club.

Pyzik
6 June 2017, 04:46
That's a nice line up of parts.

GOST
6 June 2017, 07:39
Look forward to seeing it finished.

Nice list.

First SBR, you must be excited..I need to join the club.

Yes you do.

cjd3
6 June 2017, 17:54
http://i.imgur.com/zuNYBZb.jpg

cjd3
6 June 2017, 17:55
http://i.imgur.com/2Y8sCHW.jpg
A little bit longer, but a little bit quieter.

cjd3
6 June 2017, 18:54
My only concern is the gas tube is in contact with the barrrl nut. I could file the edge down a bit for clearance, but should I go that far?

UWone77
6 June 2017, 19:05
My only concern is the gas tube is in contact with the barrrl nut. I could file the edge down a bit for clearance, but should I go that far?

I wouldn't worry about it.

Looks great. I do like some left handed shoot action

GOST
6 June 2017, 19:22
Turned out great. Is this gonna get glass, or are you staying with just irons?

cjd3
6 June 2017, 20:15
Turned out great. Is this gonna get glass, or are you staying with just irons?

At this point it's going to be irons only. I need a good rig to practice irons anyhow.

cjd3
18 June 2017, 23:44
Two trip to the range, and with good ammo, this things shoots stupid quiet. Good ammo you ask, I thought you hand loaded. Well, for the past year, I started amassing my reloading stash for 300blk. Powder, super deal on Nosler 190s, and converting a lot of brass.
Rifle is complete, let the hand loading begin. Well, initially, I was going to use Hornady AMax 208 bullets, so I cut and sized my brass to Hornady's 9th edition. Go to the range, chamber problems all over the place, click, no bang, and mortar the round out. Everything seemed correct, so I bought some factory subs. Next trip, 10 rounds unsupressed, 10 suppressed, no problems. New reloads, chamber problems, many needed mortaring. Bring the brass home, the factory brass is way shorter. Well turns out the Hornady trim data was way off, 1.390" instead of 1.358". So I've got a lot of retrims to take care of.