PDA

View Full Version : Review- Elzetta ZROC Tactical Offset Flashlight Mount



Quib
1 February 2011, 17:50
http://quib.weaponevolution.com/Elzetta ZROC Review Banner.jpg

http://quib.weaponevolution.com/ZROC SM-1.JPG

Quib
5 February 2011, 07:14
The ZROC flashlight mount made entirely in the USA by Elzetta Design LLC of Lexington, Kentucky, is manufactured from 6061-T6 aluminum with a hard coat Mil-Spec Type III anodized finish. Utilizing the included sizing adapters which can be tailor cut to fit, the mount accepts most popular brands of tactical flashlights with body outer diameters ranging from 0.70 to 1.10 inches.

A stainless steel /rubber cushioned clamp secures the operator’s light in place with the tension being adjustable by means of a captured screw with a castellated-slotted thumb nut.


http://quib.weaponevolution.com/Z1 ZROC WHT SM-3.JPG

Quib
5 February 2011, 07:17
An integrated Picatinny Rail machined into the bottom of the ZROC, gives the shooter the option of attaching additional accessories to the mount. Along those same lines, two (2) threaded holes in the upper half of the rail clamp give the operator the option of installing Elzetta’s ZPR118 Rail Kit which adds a second Picatinny Rail mounting option to the ZROC.


http://quib.weaponevolution.com/Z2 ZROC WHT 1 SM-4.JPG

http://quib.weaponevolution.com/Z2.1 ZPR118 Kit.jpg

Quib
5 February 2011, 07:19
Designed to attach onto Mil-Std 1913 Picatinny rails, the light mount is secured to the operator’s hand guards by dual castellated or slotted thumb-nuts which are also captivated to prevent loss when completely backed off or unthreaded. Measured at approximately 1.36 inches wide, the ZROC occupies only 4 slots of Picatinny rail.


http://quib.weaponevolution.com/Z3 Mount Side View Sm.JPG

http://quib.weaponevolution.com/Z4 ZROC WHT 2 SM-5.JPG

Quib
5 February 2011, 07:21
One feature which stood out to me when compared to other tactical light mounts, was the means of securing the light mount’s dual thumb-nuts. Elzetta includes two (2) stainless steel cotter pins which can be utilized to secure the slotted thumb-nuts in place, preventing loosening of the mount and the possibility of the shooter loosing his weapon light. Another option for securing the dual thumb-nuts against loosening, is through the use of stainless steel safety wire. (See Figure 1)


http://quib.weaponevolution.com/Z5 ZROC SAFETY WIRE SM-6.JPG

http://quib.weaponevolution.com/Z5.5 Safety Wire Cropped.jpg

Quib
5 February 2011, 07:26
Coming from an aviation background where loosening of hardware can result in catastrophic failure of components, loss of an aircraft, or worse, loss of life…safety wire is commonly used to secure critical aircraft component hardware against unwanted rotation or loosening.
(See Figure 1.5)


http://quib.weaponevolution.com/Z6 Aircraft Safety Wire.jpg

Quib
5 February 2011, 07:29
When the discussion turns towards weapons, the M60 machine gun quickly comes to mind with regards to safety wire, where safety wire was used in the security of the Gas Piston housing. (See Figure 2)

The option on the ZROC of additional light security through cotter pins or safety wire, could be beneficial to military operators who often find themselves securing accessories to their weapons with plastic zip-ties or 550 cord.


http://quib.weaponevolution.com/Z7 M60 Safety Wire Example.jpg

Quib
5 February 2011, 07:32
I can find no fault with the overall finish and machining of the Elzetta ZROC, with the fit and interaction of parts being smooth and tight. Upon first inspection, it’s quite obvious that Elzetta put much attention to detail and thought into all aspects of this tactical light mount, from the light mount design itself, to the enclosed hardware and sizing adapters and even in the well written and illustrated install instructions.


http://quib.weaponevolution.com/Z7.1 Install Instructions.jpg

http://quib.weaponevolution.com/Z8 ZROC LOW SM-1.JPG

http://quib.weaponevolution.com/Z9 ZROC SIDE SM-2.JPG

Quib
5 February 2011, 07:35
For more details on the Elzetta ZROC Tactical Flashlight Mount, please visit Elzetta’s website at:

http://www.elzetta.com

Elzetta Design, LLC
P.O. Box 54364
Lexington, KY 40555
Phone: (859) 707-7471
Fax: (859) 918-0465

John Hwang
6 February 2011, 23:47
Looks great. Nice job. I'll get the link over to them.