Results 1 to 1 of 1

Thread: M855A1 Accuracy

  1. #1
    Join Date
    Mar 2015
    Posts
    119
    Downloads
    0
    Uploads
    0

    M855A1 Accuracy

    M855A1 Accuracy and Velocity





    M855A1 ammunition is manufactured at the Lake City Army Ammunition Plant near Independence, Missouri. The lot of Lake City M855A1 ammunition that was evaluated for this article was manufactured in January of 2021. There were no malfunctions of any kind for this ammunition in any of the four barrels that were used in this evaluation.

    M855A1 is packaged in kraft boxes with 30 rounds in each box. The rounds are on stripper clips with 10 rounds per clip.








    The M855A1 cartridge has a nominal over-all length of 2.250”. This over-all length gives the A1 projectile a jump of 0.132” to the lands of a Colt 5.56mm NATO chamber.

    M855A1 is loaded in Lake City brass. The brass cases have the annealing iris still visible. The headstamp for this lot reads: ”LC - 21” along with the NATO cross (however, M855A1 is not a NATO load). The case-head stamp exhibits the octal station identifiers used on Lake City SCAMP machinery. The primer pocket has four “stab” crimps and a minimal amount of sealant. The case mouth has a generous amount of asphalt sealant and is crimped into a cannelure on the bullet.
















    Lake City M855A1 ammunition is charged with the St. Marks Powder SMP-842, which is a flattened ball powder. Sampled powder charges had an average weight of 26.4 grains.








    The M855A1 bullet is considered a 62 grain round, however, sampled bullets had an average weight of 62.6 grains. The M855A1 projectile is constructed from three different components; a solid copper core, an exposed steel penetrator and a reverse-drawn copper jacket that holds the other two components together. Since this bullet does not have a lead core, the only thing that fragments upon terminal impact is the copper jacket.

    It has been reported that with early lots of M855A1, it was possible to “spin” the steel penetrator inside the copper jacket with your fingers. This did not occur with any of the current rounds that I sampled.








    The M855A1 projectile has a lower specific gravity than conventional lead-core, copper jacketed bullets and is significantly longer than the legacy M855 projectile. The A1 projectiles that I sampled had a nominal length of 1.00”. According to Ballistic Performance of Rifle Bullets by Bryan Litz the G1 ballistic coefficient of M855A1 is 0.291. The same reference states that M855A1 has a nominal gyroscopic stability factor of 1.41 when fired from a barrel with a 1:8" twist and 1.85 when fired from a barrel with a 1:7" twist.
















    Velocity


    I chronographed the Lake City M855A1 ammunition from a semi-automatic AR-15 with a chrome-lined, NATO chambered, 20” Colt A4 barrel with a 1:7” twist.








    Chronographing was conducted using an Oehler 35-P chronograph with “proof screen” technology. The Oehler 35-P chronograph is actually two chronographs in one package that takes two separate chronograph readings for each shot fired and then utilizes its onboard computer to analyze the data to determine if there is any statistically significant abnormality in the readings. If the readings are suspect, the chronograph “flags” the shot to let you know that the data is invalid. There was no invalid data flagged during this testing.

    The velocities stated below are the muzzle velocities as calculated from the instrumental velocities using Oehler’s Ballistic Explorer software program. The strings of fire consisted of 10 rounds over the chronograph.












    Each round was single-loaded and cycled into the chamber from a magazine fitted with a single-load follower. The bolt locked-back after each shot allowing the chamber to cool in between each shot. This technique was used to mitigate the possible influence of “chamber-soak” on velocity data. Each new shot was fired in a consistent manner after hitting the bolt release. Atmospheric conditions were monitored and recorded using a Kestrel 4000 Pocket Weather Tracker.








    Atmospheric conditions


    Temperature: 76 degrees F

    Humidity: 47%

    Barometric pressure: 30.09 inches of Hg

    Elevation: 950 feet above sea level




    The muzzle velocity for the 10-shot string of the Lake City M855A1 ammunition fired from the 20” Colt barrel was 3131 FPS with a standard deviation of 18 FPS and a coefficient of variation of 0.59%.


    For those of you who might not be familiar with the coefficient of variation (CV), it is the standard deviation, divided by the mean (average) muzzle velocity and then multiplied by 100 and expressed as a percentage. It allows for the comparison of the uniformity of velocity between loads in different velocity spectrums; e.g. 77 grain loads running around 2,650 fps compared to 55 grain loads running around 3,250 fps.

    For comparison, the mil-spec for M193 allows for a coefficient of variation of approximately 1.2%, while one of my best 77 grain OTM hand-loads, with a muzzle velocity of 2639 PFS and a standard deviation of 4 FPS, has a coefficient of variation of 0.15%.








    I also chronographed the Lake City M855A1 ammunition from three different 14.5” barrels in the same manner as described above for the 20” Colt barrel. Chronographing of the 14.5” barrels was conducted immediately after the chronographing for the 20” barrel.




    A 10-shot string of the Lake City M855A1 fired from a 14.5” Hodge Defense barrel had a muzzle velocity of 2939 FPS with a standard deviation of 23 FPS.








    A 10-shot string of the M855A1 fired from a 14.5” Colt M4A1 SOCOM barrel had a muzzle velocity of 2949 FPS with a standard deviation of 17 FPS.







    A 10-shot string of the M855A1 fired from the Bravo Company 14.5" ELW barrel had a muzzle velocity of 2966 FPS with a standard deviation of 19 FPS.







    The muzzle velocities for the Lake City M855A1 are summarized in the table below.








    For comparison, the next two tables show the muzzle velocities for legacy military 5.56mm ammunition that also uses 62 grain projectiles: M855 and MK318 Mod 0.













    Accuracy


    I conducted an accuracy (technically, precision) evaluation of the Lake City M855A1 ammunition following my usual protocol. This accuracy evaluation used statistically significant shot-group sizes and every single shot in a fired group was included in the measurements. There was absolutely no use of any group-reduction techniques (e.g. fliers, target movement, Butterfly Shots).

    The shooting set-up will be described in detail below. As many of the significant variables as was practicable were controlled for. Also, a control group was fired from the test-rifle used in the evaluation using match-grade, hand-loaded ammunition; in order to demonstrate the capability of the barrel. Pictures of shot-groups are posted for documentation.

    Shooting was conducted from a concrete bench-rest from a distance of 100 yards (confirmed with a laser rangefinder.) The barrel used in the evaluation was free-floated. The free-float handguard of the rifle rested in a Sinclair Windage Benchrest, while the stock of the rifle rested in a Protektor bunny-ear rear bag. Sighting was accomplished via a Leupold VARI-X III set at 25x magnification and adjusted to be parallax-free at 100 yards. A mirage shade was used. Wind conditions on the shooting range were continuously monitored using a Wind Probe. The set-up was very similar to that pictured below.








    The Wind Probe.





    The test vehicle for this accuracy evaluation was one of my semi-automatic precision AR-15s with a 20” stainless-steel Lothar-Walther barrel. The barrel has a 223 Wylde chamber with a 1:8” twist. Prior to firing the Lake City M855A1, I fired a 10-shot control group using match-grade hand-loads topped with the Sierra 77 grain MatchKing (without a cannelure). That group had an extreme spread of 0.56”.
















    the control group . .







    Three 10-shot groups of the Lake City M855A1 ammunition were fired in a row with the resulting extreme spreads:

    1.78”
    2.65”
    1.78”

    for a 10-shot group average extreme spread of 2.07”. The three 10-shot groups were over-layed on each other using RSI Shooting Lab to form a 30-shot composite group. The mean radius for the 30-shot composite group was 0.63”.




    The smallest 10-shot group . . .






    The 30-shot composite group . . .







    In the category of useless trivia, the M855A1 bullet cuts the cleanest holes in paper targets of any 5.56mm/223 Remington ammunition that I’ve ever tested. It’s like wad-cutters for the AR-15.












    I also fired a 10-shot group at 100 yards off of sand-bags from each of the 14.5” barrels that were used in chronographing the M855A1 ammunition.




    A 10-shot group fired from the Colt M4A1 SOCOM barrel had an extreme spread of 1.85”.







    A 10-shot group fired from the Bravo Company 14.5" ELW barrel had an extreme spread of 2.15”.







    A 10-shot group fired from the 14.5" Hodge Defense barrel had an extreme spread of 2.51".







    Lastly, for any Internet Commandos in our viewing audience today, here’s a pic of a sub ¾ MOA group of the Lake City M855A1 ammunition fired at 100 yards. The group has an extreme spread of 0.59”.








    Last edited by Molon; 26 June 2022 at 12:11.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •