Results 1 to 13 of 13
-
28 September 2009, 20:36 #1
My First AR15 Build M4 14.5" Profile
I plan on attaching an Eotech XPS to the top. It's intended to be my budget home defense/CQB build.
Lowe Receiver: Charles Daly Defense
- Magpul ASAP Ambidextrous Sling Attachment Point
- Magpul Enhanced Trigger Guard
- Magpul CTR Collapsible Stock
- Hogue AR-15 Rubber Grip
- D&A Parts and Trigger
- DSA Buffer Tube
Upper Receiver: DSA Upper
- FSC556 Flash Suppressor and Compensator
- A.R.M.S. Gas Block/Folding Front Sight
- Adco 14.5" 1/7 Twist Barrel
- Magpul Moe Handguard
- BMC Bolt Carry Group
- BMC Charging Handle
- BMC Dust Cover
- BMC Forward Assist
Accessories:
- Tango Down Vertical Grip
- VLTOR Scout Flashlight Mount
- Fenix TK11R2 240 Lumens 1.5 Hours 90 Lumens 10 Hours
- Fenix Pressure Switch
Last edited by BrassSlinger; 28 September 2009 at 20:57.
-
28 September 2009, 21:47 #2
I like most of it, but that coiled cord may give you problems at the worst time. Have you thought about what you are going with for a rear sight, or are you going optic only?
-
28 September 2009, 21:52 #3
-
28 September 2009, 21:55 #4
The coiled cord was the first thing that I looked at as a possible negative as well (more likely to get snagged on something). The Fenix light looks promising though. I only have a small AA version, but it has worked well. Maybe look into a straight cord if it is offered, or set it up using just the rear tail-cap switch.
Just out of curiosity, what made you go with the FSC556?
-
28 September 2009, 22:12 #5
So far I love the Fenix flashlights, for the price it's hard to find another light that matches its performance in batter life and output. I took that flashlight to the gulf with me this summer and had in my pocket while I was in the water for 3 hours, it function fine and never had any problems. The only draw back with Fenix is the lack of pressure switch options and do be honest the pressure switch itself feels cheap. I am going to play with this setup and see if it works out.
I used the FSC556 because I liked the flash hider and muzzle break functionally, I had one on my previous rifle and I was impressed with its performance. I also need a muzzle device that meet the legal requirements to make the 14.5" barrel legal when pined. What would you have used instead?
-
29 September 2009, 00:22 #6
-
29 September 2009, 06:37 #7
Nice looking carbine. How sturdy is the Tango Down Vertical grip on your MOE? I haven't run that combo yet.
-
29 September 2009, 08:54 #8
-
29 September 2009, 11:04 #9
-
29 September 2009, 20:43 #10
Since it's a shorter barrel rifle built for CQB and close range shooting, suppressing the flash is not my highest priority since the bad guys would likely know where you are shooting from. Now If I was building an SPR with an 18" barrel used for longer range engagements and maybe scouting and snipping the flash suppressor would be a much higher priority.
Although I never plan on getting into a gun fight that was my logic when building this rifle.
-
1 October 2009, 09:02 #11
I got a Magpul hanguard as well, and noticed the same problem man. It's not much, but it moves around a little bit. I'm not particularly fond or the slight play, but since it's not a free floating handguard, I'm not too concerned. I also have a forward grip mounted underneath, but only really use it as a reference point for my reaction hand. As long as you keep the butt of the weapon pulled tight into your shoulder when you're shooting, you should be fine.
As far as a pressure switch goes for your light. It's not really needed, and can be activated at the wrong time by accident. I have a an flip IR filter for my Surefire that I keep closed to prevent it from shining by mistake, and open it when needed. But that's just my preference, use what works for you bro.
-Los
"I like my weapons like I like my women, slightly dirty, and well lubed."
-
3 October 2009, 20:58 #12
Alight I think its now completed.
-
4 October 2009, 08:37 #13Banned
- Join Date
- Jun 2009
- Posts
- 81
- Downloads
- 0
- Uploads
- 0
Looks like a solid piece. Good work!
Chris