Results 1 to 15 of 63
Hybrid View
-
2 December 2007, 12:04 #1
AR15 Refinishing Discussion Thread
I have a guide on Refinishing AR15s with Norrells MolyResin posted at the below link.
Please feel free to post questions, comments, suggestions, or lessons learned here.
NORRELLS AR15 REFINISHING GUIDE
.Last edited by Stickman; 7 March 2009 at 12:57.
-
3 November 2008, 11:13 #2Rktman Guest
I have an old Bushmaster lower that is turning that red color. I would like to refinish it, so I'm seaching for the black that would match my Noveske N4 upper the best. Any opinions on which black would match best?
-
3 November 2008, 19:04 #3
The Norrells SOCOM black would be a good match for most of the current receiver finishes. Its a very flat black, but part of that depends on application method.
-
18 February 2009, 17:27 #4
Stick, I have a question,
Can I recoat and/or apply different colors of molly once I have baked for an hour.
As you mentioned how you paint the parts, reassemble, paint again, then bake. Can I paint everything again after I bake once? I guess thats what I'm asking.
Thanks,
-
18 February 2009, 19:27 #5
-
18 February 2009, 19:49 #6
-
18 February 2009, 18:23 #7
-
18 February 2009, 19:28 #8
-
17 March 2009, 17:07 #9Member
- Join Date
- Feb 2009
- Location
- Louisiana, USA
- Posts
- 4
- Downloads
- 0
- Uploads
- 0
Norells on blued firearms
Stick,
Any special prep using Norells on blued firearms...will it adhear any differently than on a parked surface?
Thanx in advance!
-
17 March 2009, 23:42 #10
Parkerized steel is the best, and its surface soaks it in. Bluing is hard to coat, and giving it a quick sand blasting would certainly yield better results. I want to say that the www.molyresin.com webpage talked a bit about coating over a blued surface.
http://www.molyresin.com/molyresin_tips.asp
Pretreatment: All Metals
The surface of the parts to be coated should be clean and free of any oils, solvents, etc. Best adhesion is a freshly abrasive blaster surface using 60 to 90 grit aluminum oxide at 60 to 80 psi. Best cleaning methods appear to be soap and water; however, a chemical cleaning with MEK, acetone, etc. is also acceptable. The dullest finish for each color is achieved by abrasive blasting before coating. This will give the best coat bonding and adhesion, as well as, uniform texture. Sandblasting removes minor scratches and metal surface imperfections. You may have varied adhesion results over a blued finish as some are too smooth to allow proper adhesion. If you rough up or totally remove the blued finish with sandpaper, you may have acceptable adhesion. Chrome or nickel-plated parts should always be abrasive blasted for best adhesion. After sandblasting, rinse parts off with soap and water to remove sand dust and oil from the air compressor. In regard to air pressure used to abrasive blast the metal, use low pressure of 40 to 50 psi for aluminum and 60 to 80 psi on steel.
-
18 March 2009, 08:28 #11
This may be a little off topic but...how durable is a holographic print "dip"? Lakota Ind.
-Mitch-
-
18 March 2009, 10:46 #12
-
15 May 2009, 10:24 #13
Here was one of my first attempts. An A1 upper on a Bushmaster lower. I did the upper, not the lower.
Bigger size
http://coloradoshooting.org/v-web/ga...MT_CAR_021.jpg
I used flat black on this one. I picked up a cheap Testors brand compressor out of the model airplane aisle at Walmart for like $50. I cleaned it with whatever I had around. I put it in the oven to heat it up first. Then I sprayed it. Then I cured it in the oven.
Now my wife hates the smell, and I was almost single again for doing it. Now I do it when its warm out and she's not home. I just leave the kitchen doors and windows open.
Overall I'm happy with it. I did a CZ52 also just for fun, and a 20" AR barrel that had been turned down from an HBAR to a Govt profile. No pictures of those.
When people see it, they never assume I did the finish myself.
-
9 January 2013, 11:37 #14Member
- Join Date
- Jan 2013
- Location
- Gaithersburg MD
- Posts
- 1
- Downloads
- 4
- Uploads
- 0
Personal experience has shown that it stays around and SOLID for at least 5 to 7 years depending on usage. I have used it for a number of things around the house. It is EASY to apply - just apply it to something else first to get the hang of it.
I actually applied some to my son's rims instead of spending another grand on new ones and he gets more attention from the perceived "One Offs" that I think he would from new rims.
Just one word of caution - once you start - everything you see will look like it needs to be "dipped"!
Check out this vid for a better idea:Thanks!
Chris
If it doesn't fit - get a bigger hammer.
Blaming guns for violence is like blaming the mirror for the way you look <-- Eventually you have to deal with the CAUSE not the symptom
-
7 February 2013, 07:56 #15New Member
- Join Date
- Oct 2011
- Posts
- 13
- Downloads
- 1
- Uploads
- 0
I've used Moly resin once before and it turned out great. In regards to the thermal curing, does anyone have experience with coating Magpul products and curing them at a lower temp for a longer duration? I see one of the post here mention plastics but doesn't specifically talk about Magpul products.