Results 181 to 195 of 236
Thread: Bolt Gun Thread
-
3 January 2018, 20:28 #181
OMG this thread is awesome.
-
3 January 2018, 22:18 #182
-
4 January 2018, 02:22 #183
What he said^^
Nice rifle...maybe try another mount? Scope is new?
-
4 January 2018, 06:58 #184
Thanks for the feedback. This is the scope mount: https://zrodelta.com/product/dloc-m4-scope-mount/
No tilt. I’ve used on several ARs without an issue. Scope is a few months old (Leupold VX6HD 2-12).
-
4 January 2018, 09:32 #185
Could always get something similar to this, with some MOA built in.
https://www.larue.com/products/larue...ount-qd-lt112/-One Nation, Under God
-"The bad news is time flies. The good news is you're the pilot." ~ Michael Althsuler
-
4 January 2018, 09:59 #186
Have you tried taking the top turret off (or loose) and repositioning the knob? Sounds simple but worth a shot.
-
4 January 2018, 10:28 #187
Wait, wait, wait. You can't get it to shoot LOW enough? Is there a zero stop type feature engaged on the elevation turret? That's probably what is preventing you from dialing down.
No need for a 20 moa mount. That would make the problem even worse. The gun would shoot higher than it is now.Will - Owner of Arisaka LLC - http://www.arisakadefense.com
-
4 January 2018, 11:02 #188
Will, I though the same for a 20moa Mount. Yes, it won’t shoot low enough. I’m hitting 5” too high and I can’t get it to come down.
And yes it has a zero stop. I removed the cap on the turret to get further rotation but it’s at the true bottom. The windage also has zero stop but that one adjusted without the cap for a wider range of motion.
I wrote Leupold to get their feedback too. Probably something simple I’m overlooking.
-
4 January 2018, 11:04 #189
How can windage have a zero stop? You need to be able to dial left or right. Unless it's just a detent or something similar that tells you when you're back to center.
Edit: Just looked at the VX6 manual. It's a "zero lock" rather than stop, which is essentially a detent that locks when it comes back to center so you can adjust left or right for windage.Last edited by Slippers; 4 January 2018 at 11:17.
Will - Owner of Arisaka LLC - http://www.arisakadefense.com
-
4 January 2018, 11:10 #190
Try dialing it all the way up to as high as it will go and count the number of full MOA (Mil) that you clicked. Just as an experiment see how many clicks there are from the true bottom to the true top. And then compare that to the specs. The manual I found said 70 MOA.
If it doesn't match something is amiss.
-
4 January 2018, 11:15 #191
-
4 January 2018, 12:45 #192
Update: I figured out a way to reach the real bottom on the elevation. Seems obvious now. Can’t wait to get to the range next week. Thanks for your feedback, everyone.
-
4 January 2018, 13:40 #193
-
4 January 2018, 14:08 #194
The elevation turret could be turned by a slot in the middle, a slot sized for the edge of quarter.
I thought the whole housing elevation underneath needed to turn like on my NF. Should have sat and stared at it longer to figure this out. But it dawned on me this morning and I went back and bingo.
-
4 January 2018, 14:15 #195
I’ve got some bolt gun goodness on its way. Decided to play around with my .308 700 SPS Tactical some