Results 1 to 15 of 18
Thread: 80% Lower Jig
-
29 December 2014, 00:19 #1
80% Lower Jig
Anyone finished an 80% lower themselves, and could recommend a quality jig that could be used multiple times? Any companies known for quality, and any I should avoid?
I cleaned the maintenance barn out today, and re-discovered a really quality stand-up drill press from back in my mechanic days. It has an amazing parts holder/vice built into the drill press, so I'm thinking (maybe naively) that with the right Jig set I could knock some quality lowers out for reasonable prices...
-
29 December 2014, 01:04 #2
Generally, from what I've read since I looked into this also quite a bit also is that it's best to get the jig from the same company that makes the 80% lower. I've been toying around with planning on doing the .308 from an 80% lower when I'll eventually be able to start it.
Freedom is NEVER Free. We have to work to protect it and even be willing to die to protect it.
-
29 December 2014, 01:14 #3
I'm not super knowledgeable about 80%'s so forgive me if my newb shows a little
But didn't you use to just have to drill out the FCG holes? The jigs im seeing now want you to mill out a good portion of the top of the lower. Are there two different types or did the laws get stricter?
-
29 December 2014, 01:39 #4
with 80% lowers you have to drill out and mill the entire fire control chamber plus the FCG holes. If you go to EP armory's website they have links to some videos showing it done on their 80% polymer lowers. It's pretty much the same for doing it with an aluminum lower.
Freedom is NEVER Free. We have to work to protect it and even be willing to die to protect it.
-
29 December 2014, 01:50 #5
Can a drill press handle the milling tasks or is a dedicated piece of equipment involved?
Are the jigs full proof or will I screw up a couple in the learning curve phase?
-
29 December 2014, 03:11 #6
I've not done one myself but have seen a few done. The drill press will work. The finished product is no where as clean as a 100% lower though. These days though you can buy a 100% cheaper than a 80%. I've seen 100% lowers for as low as $39.
-
29 December 2014, 03:43 #7
I'm not counting my eggs before the hens so I haven't said much, but i'm trying to up my gunsmithing game as a side income (or partial payment for my addiction). I've been slowly acquiring quality tools, and I figured this would give me another gadget in the bat belt of tricks.
The pros I see, custom work (rollmarks, cerakote, nickel boron etc) can be done without FFL hassles. No serial #'s. And honestly the Jigs I've seen are less then 100$ and I have the major equipment already collecting dust...seems i could re coop that cost fairly quickly with just a few lowers I do myself..
But please, I'm new at this, if i'm making a mistake not only tell me, but shake, cuss and beat me into reality lol
-
29 December 2014, 04:20 #8
You won't be able to sell completed 80% lowers which I'm sure you know. Most people I know don't mess with the 80% lowers since the market is so saturated that 100% lowers are cheaper. To me the 80% lowers are nothing more than a novelty.
-
29 December 2014, 04:23 #9
-
29 December 2014, 04:34 #10
-
29 December 2014, 04:37 #11
I just figured it would make for some extremely cool one-offs
-
29 December 2014, 04:48 #12
I think with a mill, you could do some extremely cool one off lightweight units for those guys that don't like the roll marks and all the other markings. I know a few 3 gun guys that have swiss cheese ultra lightweight lowers and that's their number one complaint is the asthetics of it
-
29 December 2014, 04:50 #13
Don't know if this will be offered again, but if I'd the revenue I would've done this.
http://www.ar15news.com/2014/09/19/m...-cmt-tactical/Last edited by GOST; 29 December 2014 at 11:02.
-
29 December 2014, 07:23 #14
Really simple to finish a lower with even a drill press. The jigs with the replaceable plates and drill bushings are the best. Not all jigs fit all lowers. At this point I use the jigs just as a reference and do the milling freehand with a x y table on a quality drill press. Ares makes nice jigs along with a good bit of others for a decent price. I use this jig. Not inexpensive but very accurate.
http://www.cncguns.com/tooling.html
And for the lowers these are the best I have used. Same lower blanks as the Joe Bob's and a few others.
https://newfrontierarmory.com/shop/8...ower-receiver/
-
16 January 2015, 13:05 #15New Member
- Join Date
- Jan 2015
- Posts
- 2
- Downloads
- 0
- Uploads
- 0
Has anyone looked into Modulus Arms? I've got all of the parts (jig, 80% lower and recommend end mill bit) and will start the "milling" process in a couple of weeks. The reason I mention this company is they recommend a router instead of a drill press.