Results 466 to 480 of 502
Thread: Forward Controls Design ABC/R
-
12 September 2017, 08:59 #466
-
12 September 2017, 09:22 #467
Nooooo
How about Fashion Controls Design?
SBCG's taking longer because we rejected the size of the logo on the carrier, it was too big and ostentatious. We're not out here selling a brand, the logo needs to be far more discreet and small, or not be there at all, the logo has no active role other than an identifier. We'll laser engrave it so the lines can be thin and the size between 0.25 and 0.35.
That's about as much fashion as I can handle
-
12 September 2017, 09:33 #468
You should sell the first ones that have the big logo with a gold embossed card that says Fabulous Controls Design. Hee hee!
Will - Owner of Arisaka LLC - http://www.arisakadefense.com
-
12 September 2017, 10:21 #469There's no "Team" in F**K YOU!
-
12 September 2017, 12:03 #470
The first one was just a rendering. I had specified that it be no larger than 0.25 in diameter, the logo ended up being 0.45
Thanks to Gost's urging today, we'll get off our butts and start working on the upper project again, both with and without FA, which goes along with our SBCG project nicely
-
15 September 2017, 20:41 #471
-
6 February 2018, 04:02 #472
-
6 February 2018, 07:31 #473
I need to send you the current production AB/R-AA to replace the one you have
These dimples were a pain to get right, the dimple pattern on the current version is larger and more closely positioned dimples, they're at at a point where they offer even more traction than serrations, even at serrations' optimal access angle.
EMR-A, AA (All Angles) will be out later this month to complement ABC/R-AA.
-
6 February 2018, 07:50 #474
Heh, the joke is on me. I thought I was running the current version.
-
6 February 2018, 08:05 #475
There were some inconsistencies with the dimples as pointed out by others last year during their introduction. These were simply tossed or returned to the shop, not too many of them made it out, we were hand picking each and every dimpled bolt catch after we realized the inconsistencies.
These inconsistencies have been eliminated :)
-
6 February 2018, 13:02 #476
Dimples.
I actually need to pic up another serrated so I can put the dimples on my .308.
SPR by Damage Photos, on FlickrGround Defense 1, Blade Defense 1, Defensive Pistol 1 & 2, Aliance Shoot House, When Things Go Bad, YSINTG, Carbine 1, DART Medical, NRA Range Safety Officer
david@damagephotos.com
Damage Photos on Facebook
@damage_photos on Instagram
Use DAMAGE15 to save 15% at Third Pin Threads
Save 10% "JOINORDIE" http://cmttac.com/
-
2 May 2018, 21:49 #477
-
3 May 2018, 07:32 #478
-
3 May 2018, 23:33 #479
Really looking into going all AA on my next build. Any time frane when they will be available on the SLCF?
-
4 May 2018, 08:25 #480
We're working to buy some serrated and dimpled v2s back from dealers that have more than they need and can part with some, so SLCF will be back in stock again in a week or so, with serrated and dimpled ABC/R v2 options
Speaking of AA, the dimpled surface took a little more than a year to become popular. For a long time, serrated outsold dimpled by a large margin. Then in 2018, folks realized the AA surface has more traction than serrated, and is more versatile, the initial resistance to change the classic horizontal serrations melted away for them.
We made our projections based on existing sales numbers, and due to the popularity of the serrated surface (on bolt catches and ambi mag releases), we didn't order that many dimpled units, which combined with the AA's surge in demand, will mean a constant shortage till we catch up on dimpled production mid 2018.Last edited by Duffy; 4 May 2018 at 08:31.