Results 31 to 45 of 67
-
13 May 2015, 07:15 #31
That's a Forward Controls Design ABC/R bolt catch. In my opinion it's the best catch on the market. You can't really appreciate it until you get one installed on your gun and operate it a few times. Even though it looks awesome, in use is when it really shines.
Roger, the owner of FCD, is on this forum. I think his name is Duffy. Super cool dude. He's the guy I got this WarSport upper from.
-
13 May 2015, 07:30 #32
-
13 May 2015, 08:02 #33
Oh. Sorry. It's a Strike Industries catch and Battle Arms button.
-
13 May 2015, 09:47 #34
Aaron you should post that pic to our FB page. I'm sure Jeff at CMT would love to see this beauty.
-
13 May 2015, 11:15 #35
-
13 May 2015, 11:31 #36
-
13 May 2015, 12:03 #37
-
13 May 2015, 12:05 #38
-
13 May 2015, 12:06 #39
-
13 May 2015, 12:11 #40
-
13 May 2015, 12:13 #41
I'll fully admit that I'm completely an Instagram whore...
UWone77, Which picture would you like me to post? I'll go throw it up there. I need to wip out the DSLR and take some good pics but it's not where I want it to be yet so i'm trying not to whore..it..out..yeeeaaaah
Okay. I weighed the WarSport / CMT fully dressed with a loaded Hexmag.
9lbs 13.10oz.
-
13 May 2015, 12:17 #42
-
13 May 2015, 12:17 #43
-
21 May 2015, 11:20 #44
Slight update for this guy. Finally got the lower engraved. It's going this weekend for Cerakote on the upper / lower / rail. I've also got a Lantac E-BCG for it. I'm thinking I'm going to pull the BattleComp 1.5 off this thing and throw on an AAC 51T QD brake so I can run my suppressors on it. I've yet to see someone running a suppressed LVOA. I'm also going to pull the factory "tuned" gas block and throw on a Syrac Adjustable gas block so I can turn the gas down for running suppressed (and without) and really set the system up to be a top performer.
Also, I've been busy with work but I'll pull the rail off for your guys tonight and weigh it. Anyone want weights of anything else? Barrel or anything? It's got to come out anyway so I don't mind.
-
21 May 2015, 11:26 #45
Oh, another cool thing. I don't like the SI magazine release very much on this thing. Cross Machine Tool removed the gates around the magazine release baron their ambi lowers for some reason, so when depressing the longer Battle Arms EMR the magazine release all the way, the arm can free swing causing the release not to reset. If you don't press the button too hard it's not an issue, but it's a failure point that needs to be removed. I figure either the hole on the EMR isn't tapped deep enough or the threaded lever on the arm is a little too long. Either way, it's an issue. A Mil-Spec magazine release causes the same issue - so it's not an EMR problem. So, I've been thinking about how to solve this. I could always just chop the threaded arm on the magazine release and bring the assembly in the small distance it needs to come so I'm going to try that tonight and see how it works. In the mean time I've started modeling a new magazine release based off of the CMT lower dimensions. In my mind and my design the release sits flush with the outer limits of the body when at rest but on activation has a small protrusion that keeps this problem I am seeing from happening. I also think the Mil-Spec releases are two piece and my design is a solid piece. Is it the easiest and cheapest way to solve this problem? No...but what the hell.