Results 1 to 15 of 75
Thread: New PMAG vs old PMAG
-
8 February 2009, 18:55 #1
New PMAG vs old PMAG
There are a bunch of threads on other boards talking about the differences between the "M" PMAG, and the original version. I don't look at there being a large difference between them in term of actual functionality, but a few differences were done in the new molds. The below images should show you how to quickly tell what you are looking at.
First, here is a picture showing the different PMAGs. Starting from the far left, we have the old PMAG, the windowed PMAG, new "M" PMAG, EMAG (export mag), and 20 round PMAG.
Last edited by Stickman; 8 February 2009 at 19:01.
-
8 February 2009, 18:57 #2
You can see here that the new PMAG and EMAG have feedlip covers that attach to the bottom of the magazine body.
Last edited by Stickman; 8 February 2009 at 19:01.
-
8 February 2009, 18:58 #3
Older PMAG shown on the left in both images, new one on the right. This shows the upper and lower sections of the magazine spine.
-
8 February 2009, 18:58 #4
This shows the body ribbed sections have been changed, and there are now 3 larger panels instead of 4. The ribs are slightly thinner than the older versions, and do not protrude as much. The difference is small, but its there. The old PMAG had a cutout for the window insert, the new one does not.
-
8 February 2009, 19:04 #5
With the old on the left, and new on the right again, you can see the floorplates are different, and the new ones are marked with a "M", so it would be hard to confuse them.
From the top view, you can see the follower, and the front of the magazine is different on the inside. The new follower is also marked with the "M".
-
8 February 2009, 19:07 #6
You can also check on the date code, and you will see that there is the "M" stamped there.
So there you have it, the body, follower, and baseplate are all marked with the "M". For those who looked closely, you can also see that the magazine insert which locks into the floorplate is a different color as well.
-
8 February 2009, 19:15 #7saor32 Guest
Will the E-Mags be available in the US, or only for export?
-
8 February 2009, 19:20 #8
-
8 February 2009, 19:31 #9
Member
- Join Date
- Oct 2007
- Location
- Republic of Texas
- Posts
- 332
- Downloads
- 0
- Uploads
- 0
Are there any newly built in improvements or is this just a mold and model change?
TIA,
TS
-
8 February 2009, 19:44 #10
TS.
I've got no doubt there are a number of improvements. Someone was nice enough to IM me and comment that the ability to use stripper clip guides is improved. The dustcover slipping onto the bottom is an improvement according to the group that asked for that particular modification. The minor variance in the front must make a bit of difference as well (when viewed from straight down).
For the vast amount of PMAG users? I doubt we will see any difference at all. I think this is more a change or update of molds, and a few minor tweaks with the new design. As far as functional differences, I don't think there really are any.
-
8 February 2009, 19:53 #11
Member
- Join Date
- Oct 2007
- Location
- Republic of Texas
- Posts
- 332
- Downloads
- 0
- Uploads
- 0
-
8 February 2009, 22:53 #12
An exceptional primer on what has, to this point, been a rather subtle list of differences. Thanks, Stick.
Now ... prepare for the inevitable avalanche of "I want to buy some PMAGs. How can I make sure I'm getting the new version?" posts all across the web.
AC
-
10 February 2009, 10:31 #13
Next dumb question: will there be M series Maglevel setups?
-
10 February 2009, 11:52 #14
I'm assuming the new M will replace the standard Pmags we're all used to?
Does that mean there will be no more windowed Pmags?
-
10 February 2009, 17:49 #15
Jeffy,
There are no more of the original PMAGs being built as far as I know, everything is going to be the new one.
Guessing on the windowed mags would be just that, a guess. I think at some point, the molds will need to be replaced, and that we would see similar changes then.