SMOS Build Thread

**titanse05** · 2 February 2016, 15:29

Originally Posted by Pyzik

I've never had an issue with pins.

Sent from my SM-N910V using Tapatalk

Me neither.... until last Friday. Lol

I think it will make it easier and be quicker. I will report back once my bolt catch arrives.

**titanse05** · 2 February 2016, 16:32

Enough blabbing, here is a quick picture of mine.

**Pyzik** · 2 February 2016, 18:24

Originally Posted by titanse05

Enough blabbing, here is a quick picture of mine.

😍😍 I like the gray!

Progress

Sent from my SM-N910V using Tapatalk

**Josh S.** · 2 February 2016, 18:53

Originally Posted by Pyzik

�� I like the gray!

Progress

Sent from my SM-N910V using Tapatalk

Okay that CMC looks badass paired with the SMOS set! Just when I think I have my mind made up on a Geissele... lol

Also what dust cover is that?! I think this build is deserving of something other than mil-spec.

**Dstrbdmedic167** · 2 February 2016, 19:08

Originally Posted by Josh S.

Also what dust cover is that?! I think this build is deserving of something other than mil-spec.

Strike Industries UDC.

**Pyzik** · 2 February 2016, 19:24

Originally Posted by Dstrbdmedic167

Strike Industries UDC.

Bingo. Their plain one. I wanted a V7 port door but just couldn't justify almost $50.
Also digging the SI pins. Not sure how I feel about their mag release bar. Finish isn't near as nice as the pins.

Thanks.
I knew the CMC would look good in it.

Sent from my SM-N910V using Tapatalk

**Josh S.** · 2 February 2016, 19:35

Did you get the regular or "Enhanced" UDC? Says on their website you have to use the Enhanced for some billet uppers.

That SI pin flows with the lines so well I didn't even realize you had it installed lol. Looks good.

**EO3** · 2 February 2016, 19:40

Originally Posted by Pyzik

😍😍
Progress

Looking good!!! Are those the stock trigger pins for the CMC?

What safety selector are you going with?

**Pyzik** · 2 February 2016, 19:41

Originally Posted by Josh S.

Did you get the regular or "Enhanced" UDC? Says on their website you have to use the Enhanced for some billet uppers.

That SI pin flows with the lines so well I didn't even realize you had it installed lol. Looks good.

It's the enhanced.
It is slightly harder to close than a milspec.

Sent from my SM-N910V using Tapatalk

**Deadwing** · 2 February 2016, 19:43

Originally Posted by Pyzik

Bingo. Their plain one. I wanted a V7 port door but just couldn't justify almost $50.
Also digging the SI pins. Not sure how I feel about their mag release bar. Finish isn't near as nice as the pins.

Thanks.
I knew the CMC would look good in it.

Sent from my SM-N910V using Tapatalk

I bought an SI mag catch for my GFY build. Finish on mine is about on par with milspec. But hey, it's stylized. I went with a milspec dust cover on mine. My lower is finished as of last night. I went with an ALG ACT that i had sitting around for the trigger, Forward Controls ABC/R, BAD pins and safety, with a MOE K2 and CTR in grey for furniture.

I'm waiting on my goofy sized crowfoot wrench to arrive to finish the upper, which is getting a Centurion Arms 16" CHF barrel and BCG, BCM Mod 4 CH, Magpul MBUS Pro BUIS, and a BattleComp 1.0. Optic TBD.

**DutyUse** · 2 February 2016, 19:47

Originally Posted by Deadwing

I bought an SI mag catch for my GFY build. Finish on mine is about on par with milspec. But hey, it's stylized. I went with a milspec dust cover on mine. My lower is finished as of last night. I went with an ALG ACT that i had sitting around for the trigger, Forward Controls ABC/R, BAD pins and safety, with a MOE K2 and CTR in grey for furniture.

I'm waiting on my goofy sized crowfoot wrench to arrive to finish the upper, which is getting a Centurion Arms 16" CHF barrel and BCG, BCM Mod 4 CH, Magpul MBUS Pro BUIS, and a BattleComp 1.0. Optic TBD.

That should turn out wicked

**Pyzik** · 2 February 2016, 20:04

Originally Posted by DutyUse

That should turn out wicked

Agreed!

Sent from my SM-N910V using Tapatalk

**EO3** · 3 February 2016, 15:53

Just throwing this out here to see if anyone is interested:

I have a 14.5" Faxon Gunner barrel that I am wanting to part ways with. Muzzle brake was NOT pinned because it is SBR'd. It has hardly been used at all. Didn't count carefully, but probably between 100-150 rounds through. I'd sell it with the Faxon gas block and tube as well. Just seeing if anyone might be interested! I currently have it on a build with the SMOS SM13 rail, and it fits very nicely with it. Comes out just past the rail without a muzzle device.

**Dstrbdmedic167** · 3 February 2016, 15:55

Originally Posted by EO3

Just throwing this out here to see if anyone is interested:

I have a 14.5" Faxon Gunner barrel that I am wanting to part ways with. Muzzle brake was NOT pinned because it is SBR'd. It has hardly been used at all. Didn't count carefully, but probably between 100-150 rounds through. I'd sell it with the Faxon gas block and tube as well. Just seeing if anyone might be interested! I currently have it on a build with the SMOS SM13 rail, and it fits very nicely with it. Comes out just past the rail without a muzzle device.

Post it in the classifieds. It'll sell...

**Battle Cock** · 3 February 2016, 16:12

Originally Posted by titanse05

Enough blabbing, here is a quick picture of mine.

Straight sexy.

Thread: SMOS Build Thread

Thread Tools

Display

Posting Permissions