SMOS Build Thread

[Mecha_Arms]

The IMOD is a great stock. Both functional and stylish. I've got only one gripe with it, and that would be that it likes to grab my beard every now and then.

I had a similar problem with an EMOD. Still like the stock, but I've been mulling over replacing it with something else.

[EO3]

I bought the full set, and I can't decide on a few things. My set is off to get Cerakoted in Magpul FDE right now
Here's what I have so far:

Upper -
GFY Receiver
V7 Lightweight Door
Lantac E-BCG
(Not sure about CH, eyeballing the new Geissele ambi one)
GFY Rail
(Not sure about barrel - Either 16" or 18" - anyone have suggestions? (been looking at Ballistic Advantage Hanson Series))
(also haven't picked a muzzle device)

Lower -
GFY Receiver
CMC Flat 3.5
BAD EPS Pins
BAD ASS Safety
Strike Industries Mag Release
Strike Industries Bolt Catch/Release
Magpul K2+
(Can't decide on Magpul MOE Fixed Rifle Stock or Magpul SL-S or STR)

Optic options are wide open - Haven't really picked this rifle's purpose yet.

Anyone have any suggestions on any of this?

[Deadwing]

I had a similar problem with an EMOD. Still like the stock, but I've been mulling over replacing it with something else.

I've got an EMOD on my SPR that i keep thinking about replacing as well. It's a great stock, but damn the beard pulling. I may just replace it with a SOPMOD, which is still one of my favorites.

[UWone77]

I bought the full set, and I can't decide on a few things. My set is off to get Cerakoted in Magpul FDE right now
Here's what I have so far:

Upper -
GFY Receiver
V7 Lightweight Door
Lantac E-BCG
(Not sure about CH, eyeballing the new Geissele ambi one)
GFY Rail
(Not sure about barrel - Either 16" or 18" - anyone have suggestions? (been looking at Ballistic Advantage Hanson Series))
(also haven't picked a muzzle device)

Lower -
GFY Receiver
CMC Flat 3.5
BAD EPS Pins
BAD ASS Safety
Strike Industries Mag Release
Strike Industries Bolt Catch/Release
Magpul K2+
(Can't decide on Magpul MOE Fixed Rifle Stock or Magpul SL-S or STR)

Optic options are wide open - Haven't really picked this rifle's purpose yet.

Anyone have any suggestions on any of this?

Good list of parts, but like you said, until you figure out the purpose of the gun, it will be hard to tweak.

[EO3]

I think I've decided I want to go lightweight with it and make it all purpose. I'd go with a 14.5", but I'm so indecisive about muzzle devices, I can't get myself to pin and weld one, and don't want to SBR it.

So.... I guess, suggestions for a lightweight build, anyone?

[Dstrbdmedic167]

I think I've decided I want to go lightweight with it and make it all purpose. I'd go with a 14.5", but I'm so indecisive about muzzle devices, I can't get myself to pin and weld one, and don't want to SBR it.

So.... I guess, suggestions for a lightweight build, anyone?

Going off that I'd probably use a Magpul SL stock and grip vs the above mentioned. Optics would be a red dot like an aimpoint t1(or similar) or the Trijicion MRO or something in those categories.

[UWone77]

I'm not sure a Billet Set would be the way to go on LW build.

[EO3]

I'm not sure a Billet Set would be the way to go on LW build.

Wonder how many ounces we're talking between this set and a forged set? Maybe I should be a little more specific. I definitely want to keep it lightweight, but I'm not necessarily going for BAD-LW and titanium parts lightweight, just light enough to run drills with and run around with, if that makes sense.

Has anyone tried out the Ballistic Advantage LW Hanson Barrels?

[Dstrbdmedic167]

Has anyone tried out the Ballistic Advantage LW Hanson Barrels?

Yes!?! I have the 18" standard version. So far I've been thoroughly impressed. The ballistic advantage Hanson series is one of my favorite barrels out there.

As far as the billet vs forged. As long as your not going for BAD-LW as you mentioned the billet will work but as UW mentioned isn't the lightest overall. [Insert billet vs Forged Debate]

[Deadwing]

I purchased a 16" Hanson a few months back when it was their barrel of the week. I think i paid $189 shipped, and that included a pinned low profile gas block. I share Dstrbdmedic's opinion...i'm impressed.

[EO3]

Yes!?! I have the 18" standard version. So far I've been thoroughly impressed. The ballistic advantage Hanson series is one of my favorite barrels out there.

As far as the billet vs forged. As long as your not going for BAD-LW as you mentioned the billet will work but as UW mentioned isn't the lightest overall. [Insert billet vs Forged Debate]

Good to hear! I'm looking at the 16" .223 Wylde Stainless Lo Pro. Just can't decide if I'd want to throw a 1-4/1-6x on top or a red dot with a magnifier...

[EO3]

I purchased a 16" Hanson a few months back when it was their barrel of the week. I think i paid $189 shipped, and that included a pinned low profile gas block. I share Dstrbdmedic's opinion...i'm impressed.

Sounds like it'll be money well spent if I go with a BA Hanson.

[fledge]

The SMOS set is 18.3oz. a typical forged set is 17oz. Not much difference.

If you want lightweight, look at Faxon pencil barrels. 17.5oz for 14.5 and 19oz for 16". Not designed for precision once heated up but if your purpose is short range defensive, you're in biz.

[EO3]

The SMOS set is 18.3oz. a typical forged set is 17oz. Not much difference.

If you want lightweight, look at Faxon pencil barrels. 17.5oz for 14.5 and 19oz for 16". Not designed for precision once heated up but if your purpose is short range defensive, you're in biz.

Thanks for the weight info!

I've got a Faxon 14.5" Gunner Profile right now, and I really like it. I'm pretty much between a BA Hanson 16" or a Faxon Gunner 16" for this build.

[fledge]

Roger that. I've got an 18" gunner for my other SMOS upper.