Results 1 to 15 of 16
Thread: Rail Covers - Magpul handstop
-
13 September 2016, 08:34 #1
Rail Covers - Magpul handstop
Looking for something similar to my Noveske panels in the MLOK section. Magpul's handstop front index point looks like the money. i think I am going to have to buy two packs to get what I want though and then I'm going to have two of the larger "rear" handstops that I don't really want. Sigh.
Anyone used these? They look slightly bulkier than the Noveske, are they "bulky"?
Ground Defense 1, Blade Defense 1, Defensive Pistol 1 & 2, Aliance Shoot House, When Things Go Bad, YSINTG, Carbine 1, DART Medical, NRA Range Safety Officer
david@damagephotos.com
Damage Photos on Facebook
@damage_photos on Instagram
Use DAMAGE15 to save 15% at Third Pin Threads
Save 10% "JOINORDIE" http://cmttac.com/
-
13 September 2016, 08:54 #2
On slimmer rails they feel good. A little too bulky on larger handguards ... say greater than 1.5 ID.
-
13 September 2016, 09:12 #3
-
13 September 2016, 09:14 #4
Thank ya, gents
Sent from my SM-N910V using TapatalkGround Defense 1, Blade Defense 1, Defensive Pistol 1 & 2, Aliance Shoot House, When Things Go Bad, YSINTG, Carbine 1, DART Medical, NRA Range Safety Officer
david@damagephotos.com
Damage Photos on Facebook
@damage_photos on Instagram
Use DAMAGE15 to save 15% at Third Pin Threads
Save 10% "JOINORDIE" http://cmttac.com/
-
13 September 2016, 10:43 #5
-
13 September 2016, 10:58 #6Ground Defense 1, Blade Defense 1, Defensive Pistol 1 & 2, Aliance Shoot House, When Things Go Bad, YSINTG, Carbine 1, DART Medical, NRA Range Safety Officer
david@damagephotos.com
Damage Photos on Facebook
@damage_photos on Instagram
Use DAMAGE15 to save 15% at Third Pin Threads
Save 10% "JOINORDIE" http://cmttac.com/
-
13 September 2016, 11:18 #7
They're pretty slim overall and fit quite nicely on my SMOS GFY rail. I also agree that they are a bit aggressively textured if you aren't wearing gloves.
Graphic Designer
Instagram: @EO3actual
-
13 September 2016, 11:25 #8
-
13 September 2016, 11:35 #9
-
13 September 2016, 12:53 #10
I thought the M-Lok hand stop was one piece with a cover? Am I reading incorrectly the OP only wants to use the small part of the handstop?
There's no "Team" in F**K YOU!
-
13 September 2016, 13:03 #11Ground Defense 1, Blade Defense 1, Defensive Pistol 1 & 2, Aliance Shoot House, When Things Go Bad, YSINTG, Carbine 1, DART Medical, NRA Range Safety Officer
david@damagephotos.com
Damage Photos on Facebook
@damage_photos on Instagram
Use DAMAGE15 to save 15% at Third Pin Threads
Save 10% "JOINORDIE" http://cmttac.com/
-
13 September 2016, 13:24 #12
Griffin's may be an alternative. Just tossing it out there.
https://www.griffinarmament.com/Grif...-p/garsblk.htm
-
13 September 2016, 13:43 #13
-
14 September 2016, 09:59 #14
Pyzik, Do you need the MLOK version? I have a single Picatinny version I'm not using that can be yours for the low low price of nothing
I wonder if these panels would fit into my Parallax Tactical FFSSR rail slots. I have seen the KAC URX rail covers used on it...Griffin's probably would too
-
14 September 2016, 10:26 #15Ground Defense 1, Blade Defense 1, Defensive Pistol 1 & 2, Aliance Shoot House, When Things Go Bad, YSINTG, Carbine 1, DART Medical, NRA Range Safety Officer
david@damagephotos.com
Damage Photos on Facebook
@damage_photos on Instagram
Use DAMAGE15 to save 15% at Third Pin Threads
Save 10% "JOINORDIE" http://cmttac.com/