Results 16 to 30 of 85
Thread: SMOS Precision build
-
1 January 2017, 17:51 #16
And I'd say that even if you do want to pin the GB, give it some time and a few hundred rounds to make sure you are happy with the set up first. The GSBs don't fit well under skinny handguards, either, so if you ever change out your handguard there is a good chance you'll have to change out your gas block, too.
-
2 January 2017, 08:02 #17
I'm a fan of over-engineered stuff. I'm incredibly hard on my equipment. Buy once, cry once
Sent from my SM-G900P using Tapatalk
-
5 January 2017, 09:25 #18
Well, got off the phone with Rainier. They won't pin my gas block. Oh well
Sent from my SM-G900P using Tapatalk
-
5 January 2017, 10:39 #19
If you install it correctly, pinning isn't necessary. A real mil-spec mk12 or mk18 doesn't have a pinned gas block, and keep in mind the mk12 had the gas block exposed, not protected under a handguard. If you call up Daniel Defense and have them build you a mil-spec mk18 upper with the correct gas port size, it will also include an unpinned gas block.
BCM also doesn't pin theirs, but removing the gas block from one of their uppers is extremely difficult.
Use high temp red loctite and knurled tip set screws, along with a proper dimple in the barrel, and it's not going anywhere.Will - Owner of Arisaka LLC - http://www.arisakadefense.com
-
5 January 2017, 12:46 #20
-
5 January 2017, 13:06 #21
-
5 January 2017, 14:01 #22
I don't disagree with the intent of your post, but... MK12s get issued to not-specifically-trained-Marine-grunts. Marines in general aren't soft on gear. As for the MK18s...Lots of boat donkeys get issued MK18s, and they're not "all that" with their gear either. But I'm guessing Will isn't talking about an actual MK18 and instead meant a CQBR Block 2, in which case, both you and he has a point.
Personally, I have a few rifles that aren't pinned and don't even have red Loctite and they hold up fine (under a rail). But in a perfect world, given I don't ever want to use red Loctite, I'd pin my gas blocks if I had the means and/or the money. If for no other reason that a) peace of mind and b) I'm anti-red Loctite (because I'm lazy if/when I have to 'smith my own guns).
-
5 January 2017, 14:10 #23
Yeah Will and I talked off line about pinned GB in the past.
Do you need a pinned GB? Probably not. However a pinned GB does ensure that the GB will come off if you decide to uninstall it later on. I'm with you on Red Loctite, I have a BCM upper that they slathered red loctite on and it never budged. I've seen other guys in my department just using set screws and they eventually had GB back out.
For me pinned GB are cheap insurance and make life easier when swapping out rails & barrels.
-
5 January 2017, 15:01 #24
One question- what the actual fuck is a boat donkey
Sent from my SM-G900P using Tapatalk
-
5 January 2017, 15:38 #25
My apologies in this whole discussion...I was speaking from a recreational shooter's perspective. In any kind of service use, totally pin the GB. Because why not? I know, we're beating a dead horse.
It's a North American mammal that often lacks any kind of common sense or awareness of reality. Often times, they're witnessed to move in a path or direction that makes no sense, but it's what they know and are comfortable with because "that's what they did the last time." They are a peculiar breed, and one that will often times try and kill you if you're an outsider and/or have any outside knowledge of what happens beyond the lifelines of their tiny little ship. But at the same time, they also make your food and make sure you have a warm shower (sometimes), so it's sometimes necessary to tread lightly on their incapacity and/or deficiencies.
-
5 January 2017, 18:39 #26
-
9 January 2017, 09:49 #27
So I tried to start assembling my upper last night; all sorts of problems. First off, the Geissele gas black is giving me all sorts of hell. Couldn't get the gas tube pin in, it ate 2 pins before it finally somewhat took a 3rd, and its still not how I want it. Then, it doesn't want to seat on the barrel, its freaking tight as hell. Into the freezer it went last night, and is waiting until I get home. 3rd, and this is my boneheaded fault, as I should have freaking checked before torquing the barrel nut on, but the dust cover door is out of spec, and doesn't want to latch closed. It seems like its too small. This build is fighting tooth and nail!
Sent from my SM-G900P using Tapatalk
-
9 January 2017, 10:08 #28
Looking good. I'm in the process of an 18-20" 'SPR' now too and taking notes.
Ground Defense 1, Blade Defense 1, Defensive Pistol 1 & 2, Aliance Shoot House, When Things Go Bad, YSINTG, Carbine 1, DART Medical, NRA Range Safety Officer
david@damagephotos.com
Damage Photos on Facebook
@damage_photos on Instagram
Use DAMAGE15 to save 15% at Third Pin Threads
Save 10% "JOINORDIE" http://cmttac.com/
-
9 January 2017, 10:56 #29
Well don't take notes from me, apparently I'm an idiot
Sent from my SM-G900P using Tapatalk
-
9 January 2017, 14:44 #30
Oh, and for other people building using SMOS, your best bet for tightening the barrel nut is a crowsfoot wrench, size
1- 3/16. I ordered one off of amazon, but had to modify it with a grinder, because it was too wide to fit on the barrel nut.
Sent from my SM-G900P using Tapatalk