New Lantac muzzle device

[six8]

Wonder if this would save my light? 😁




Sent from my iPhone using Tapatalk

[DutyUse]

Awesome. Kinda makes em into a QD blast shield :D

[akersc]

Damn it guys I was done with my spreadsheet for the SBR....... Was until you all happened! I am pretty sure I need this in my life.


Sent from my iPhone using Tapatalk

[XACT_ABORT]

Pretty bad ass looking setup. I haven't ever seen any Lantac stuff in the wild outside of the Dragon. Like an upper or forend like pictured. All of the stuff they make is very photogenic... Usually makes me drool a bit.

[FortTom]

So does the brake function as normal, reducing felt recoil and muzzle flip, or does it just control muzzle flip with the device attached to the brake? LANTAC's bullet statements aren't exactly clear on this. It would still be nice to have one at the range, when shooting from the bench, so you don't fracture your neighbors to the left and right's skulls. I'm curious as to how much they will cost, also. I'd like to see some in-depth non-partisan testing done with one of these. Also, I'd like to see one for the 7.62 version.

[nCarnage]

Looking into this in the future for my finished build since it has the dragon on it. Especially for the indoor range.


Sent from my iPhone using Tapatalk

[Gaspipeshooter]

Wonder if this would save my light? 😁




Sent from my iPhone using Tapatalk

Moving it back one slot might help...

[six8]

Moving it back one slot might help...

Yeah but it's too close to my hand already. Need a new setup on this thing.


Sent from my iPhone using Tapatalk

[GOST]

Yeah but it's too close to my hand already. Need a new setup on this thing.


Sent from my iPhone using Tapatalk

An Elzetta Alpha may be short enough to help. 3.4 oz with 315 lumen output.



http://www.rainierarms.com/elzetta-a...standard-bezel

[Jerry R]

Also, I'd like to see one for the 7.62 version.

+1 on the 7.62 version - I think the Sig would like it.

[WHSmithIV]

I'm still trying to figure out what muzzle device to get for the 7.62 x 39 pistol. There just doesn't seem to be a lot of options available with the 5/8 x 24 threads. Plus, I want to get the muzzle device with brushed stainless finish for aesthetics so it will complement the upper receiver. It looks like I may just end up getting a standard birdcage flash hider in stainless though I have found a couple compensators in stainless. Might end up just flipping a coin.

[UWone77]

I'm still trying to figure out what muzzle device to get for the 7.62 x 39 pistol. There just doesn't seem to be a lot of options available with the 5/8 x 24 threads. Plus, I want to get the muzzle device with brushed stainless finish for aesthetics so it will complement the upper receiver. It looks like I may just end up getting a standard birdcage flash hider in stainless though I have found a couple compensators in stainless. Might end up just flipping a coin.

I'm a man of my word. I promised to send you a 7.62 muzzle device, and I'll get this particular one out to you next week. Perhaps you can throw up a review. In stainless steel...

http://fortismfg.com/ar10-fortis-red...agement-device

[mustangfreek]

I'm a man of my word. I promised to send you a 7.62 muzzle device, and I'll get this particular one out to you next week. Perhaps you can throw up a review. In stainless steel...

http://fortismfg.com/ar10-fortis-red...agement-device

Very stand up of you UW, damn that is a nice comp and has had my attention for a while for 556 guns, but now so with a 308 build lurking in my brain

[GOST]