AR Accessory/Parts Photo Thread

[Aragorn]

joelski, I bought a tube just like that, from 2A or V7 weapons, don't remember for my lightweight gun. Really nice, and save several ounces, maybe up to 4oz.
FT

4oz? That'd be pretty incredible weight savings, considering a mil-spec tube (BCM) only weighs 3.8oz to begin with.

Idk about V7 or 2A's version, but I've also got the PWS and when I talked to them on the phone they told me their version was .8oz less than mil-spec.

[UWone77]

Gens 2&3

[Former11B]

Geez dude lol

[FortTom]

4oz? That'd be pretty incredible weight savings, considering a mil-spec tube (BCM) only weighs 3.8oz to begin with.

Idk about V7 or 2A's version, but I've also got the PWS and when I talked to them on the phone they told me their version was .8oz less than mil-spec.

Yeah, it is amazing. My bad, I was talking the tube, end plate, castle nut, and should say about 1oz. or a hair more. Brain damaged blamed for that one. Certainly not a quarter pound.
I did, have a quarter pounder for lunch a few days ago, with fries and a coke and probably gained a quarter pound.

FT

[UWone77]

Yeah, it is amazing. My bad, I was talking the tube, end plate, castle nut, and should say about 1oz. or a hair more. Brain damaged blamed for that one. Certainly not a quarter pound.
I did, have a quarter pounder for lunch a few days ago, with fries and a coke and probably gained a quarter pound.

FT

Heh. FT that last few sentences cracked me up. Thanks for the laughs you crazy character.

[UWone77]

[Former11B]

Sweet! Perfect for a Mini4

[UWone77]

[UWone77]

[Joelski]

I need an 18" version of that in silent black. Ideas?

[Former11B]

I need an 18" version of that in silent black. Ideas?

Buy the barrel and have it cerakoted

I would mate the gas block to the barrel and use some sanding cloth to work down and spots that hang on the barrel. If it’s a snug fit, it’ll be tighter with Cerakote. MCA’s battlekitty Rifle that was cerakoted by BDL had the Rainier UM barrel done in a FDE/Khaki. I greased the hell out of the barrel and block but it was really snug. I put a small run in the Cerakote but it was covered up by the gas block and rail. If I could’ve matched the two ahead of time it would’ve been fine

[UWone77]

I need an 18" version of that in silent black. Ideas?

They should have nitrided versions out later this year. I have a prototype 7.5" somewhere.

[Pyzik]

man I think those barrels in short configuration look even better.

[Joelski]

They should have nitrided versions out later this year. I have a prototype 7.5" somewhere.

Dibs!

[Stone]

Buy the barrel and have it cerakoted

I would mate the gas block to the barrel and use some sanding cloth to work down and spots that hang on the barrel. If it’s a snug fit, it’ll be tighter with Cerakote. MCA’s battlekitty Rifle that was cerakoted by BDL had the Rainier UM barrel done in a FDE/Khaki. I greased the hell out of the barrel and block but it was really snug. I put a small run in the Cerakote but it was covered up by the gas block and rail. If I could’ve matched the two ahead of time it would’ve been fine

A while back I remember seeing a low pro gas block that was intentionally made a hair bigger to fit over cerakoted barrels. I will look around...

Heres one:http://www.blackrivertactical.com/co...tegory=6464008