Results 91 to 105 of 115
Thread: Building a Rifle for your Wife
-
18 October 2014, 21:22 #91
-
18 October 2014, 22:58 #92
-
18 October 2014, 23:05 #93
-
19 October 2014, 06:30 #94
-
19 October 2014, 11:06 #95
-
19 October 2014, 15:11 #96
-
19 October 2014, 15:23 #97
Found these. They may be a decent replacement while waiting for the pmags. https://www.wideners.com/itemdetail....m_id=100000842
-
19 October 2014, 16:28 #98
I'm a wee bit afraid to build one for my wife. She wants one in purple. I doubt I would ever want to take it to a range. I might do her an AR pistol though. Her right eye is having a problem so with a simple red dot on it she could use her left eye to sight it plus, it wouldn't be very heavy for her to hold with maybe a 20 round mag. Hmmm.... I think I just defined my next project after the 7.62x39 build without planning to....... OK WHO IS THE OP? I'm not sure I'm going to forgive you for doing this to me! ... Guess I'll have to Duracoat the parts....
Freedom is NEVER Free. We have to work to protect it and even be willing to die to protect it.
-
19 October 2014, 18:08 #99
Is the Purple I was talking about.
Recipe for purple was 20 cups near boiling water, 2 tsp Rit Purple, 1/4 tsp royal blue. Parts were heated in an oven for 5 minutes at 170. Soak time was around 1:30-2 minutes depending on part. Parts were taped off with electrical tape in this design, then redyed with RIT BlackIt's difficult to soar with eagles, when you work with turkeys...
-
21 October 2014, 11:50 #100
That came out REALLY nice camomike. Where did you get the dyes from?
Freedom is NEVER Free. We have to work to protect it and even be willing to die to protect it.
-
22 October 2014, 21:00 #101
Building a Rifle for your Wife
iPotato pic, but:
UCWRG color fill pocket lower
Chopped UCWRG grip
LWRC ultra compact stock
V7 castle nut/end plate
ALG fire control group
BAD-ASS safety w/ short levers on both sides
RRA 9mm upper with gas tube hole
V7 port door/rod
Rainier Arms Raptor
SLR 7" Solo Ultra Lite keymod
VooDoo Innovations 7.5" pencil barrel
Kineti-tech muzzle brake and shield
MP5K grip modified to keymod
MI keymod panels
Primary Arms micro red dot
Seekins absolute co-witness mount
Magpul MBUSLast edited by JoshAston; 22 October 2014 at 21:09.
-
22 October 2014, 21:16 #102
-
24 October 2014, 19:56 #103New Member
- Join Date
- Sep 2014
- Posts
- 5
- Downloads
- 0
- Uploads
- 0
-
2 December 2016, 18:36 #104Member
- Join Date
- Aug 2011
- Location
- NE Ohio
- Posts
- 37
- Downloads
- 0
- Uploads
- 0
Hope you guys don't mind me resurrecting a 2 year old thread but it seemed the most appropriate. So here's where the Recce 5 went I mentioned in the transfer time thread. Shoots great and the wife loves it, she even kept the pink to a minimum.
Lower specs:
BAD GEN 1 forged lower
BAD Ti pin set
V7 Bolt catch
V7 Mag catch
Geissele SSA
BAD Short throw selector
ERGO Grip
V7 Receiver extension, castle nut and end plate
H2 buffer
Blue Sprinco spring
MFT Minimalist stock
Upper specs:
BCM 11.5 in. ELW barrel
BCM Upper receiver
V7 Titanium gas block
BRT 0.060 Gas port insert
Griffin Armament minimalist Ti brake
LMT Enhanced carrier
Sionics NP3 bolt
BCM Ambi charging handle
MI Gen3 Lightweight Mlok handguard
-
2 December 2016, 18:48 #105
A worthy resurrection. Nice collection of parts and color accent.