Results 91 to 105 of 136
-
10 December 2014, 10:43 #91
I've got a patrol rifle class coming up, and will run one of these mags as my primary magazine. I'll report back with any failures if any. Should be a decent 500-600 round day.
-
10 December 2014, 11:30 #92
ETS mag in a magpul branded lower... So I'm guessing they'll work in a China doll?
It's difficult to soar with eagles, when you work with turkeys...
-
10 December 2014, 11:44 #93
I've been running just the one mag because I gave the other to a buddy. But I've not had a single issue at all with maybe a few hundred rounds so far.
-
10 December 2014, 12:09 #94
Maybe this is something you could look out for when you go to your class.
Had a chance to run a mag I bought from them a little while ago over Thanksgiving break. There was one time where the round failed to catch - it seemed to be due to the magazine. Looking at the round, it wasn't completely pressed against the feed lips - there was a little gap. I'm not 100% what the fault was, but there's a fair chance that it could had to do with those small squares on the inside of the magazine, just below the feed lips.
... keep in mind though, I shot the ETS mag through a MK18 - with a can, and was also the most popular (dirtiest) rental my range had ..
-
10 December 2014, 12:36 #95Senior Member
- Join Date
- Sep 2014
- Posts
- 556
- Downloads
- 0
- Uploads
- 0
I want some of these but I need more mags like I need a hole in the head. I'm a mag whore.
Sent from my iPhone using Tapatalk
-
10 December 2014, 13:10 #96
-
10 December 2014, 13:15 #97
-
10 December 2014, 14:31 #98
-
10 December 2014, 15:31 #99
-
10 December 2014, 16:40 #100
Hey Thompson,
We had one other guy experience this. He is a small maker out of TX and he was shooting our mags in an SBR 10.5" I think and it ran fine until he put the can on it. Then, every now and then he would get a FTF. After talking with him extensively about it, I told him my best guess is that it was way over gassed. He then changed to a heavier buffer and it never happened again.
Now all that said, that may nothing to do with what you experienced because this gentleman never described any gap where the round was not sitting up against the feedlip.
Please let me know if you continue to see this.
-
10 December 2014, 16:50 #101
Hey ETS,
Next time I hit the range, I'll see if I can pull out that rental/can to see if it happens again. If it does, I'll grab some pics and do some further digging. Last I was shooting with some friends, so didn't quite have some me time to mess around with the mag.
For what it's worth - I did experience a lot of jams with the DDMK18. After every couple of rounds, the round would fail fully seat in the chamber, or would have a failure to feed. But like I said, this was the dirtiest gun they had + the can. Just to prove it wasn't the magazine - I ran that same mag the same day on one of their DDM4 (not sure which). Did a mag dump and it worked flawlessly.
-
10 December 2014, 17:12 #102
-
10 December 2014, 17:52 #103
-
11 December 2014, 12:58 #104
Use code: M4CARBINE
For 20% off
http://www.etsgroup.us/ETS-Group-AR1...nes-s/1814.htm
-
11 December 2014, 13:07 #105
Thanks GOST, I'm about to order two of these.
NRA LIFE MEMBER
Veteran Combat Medic
Experience is what you get... When you don't get what you want.