Results 46 to 60 of 80
-
23 June 2015, 09:39 #46WEVO Spell Checker
- Join Date
- Sep 2014
- Location
- Florida
- Posts
- 3,198
- Downloads
- 1
- Uploads
- 0
ok this will be the mag i be using on my 300BKL upper
2 USGI and 1 Pmag Gen 1
16 upper (1 of 1)-2 by Luis f, on Flickr$300 and 10 Pastrami Sandwiches and a case of Diet Coke. ( UWone77)
-
23 June 2015, 10:14 #47
The most consistent and accurate factory loaded Blackout's I have found are the offerings from Hornady. Their subs were all within 20 FPS and also use the fantastic 208 gr. A-MAX bullets.
And stop worrying about the mags, Luis. ANY 5.56 mags will work just fine. Lol
-
23 June 2015, 10:23 #48WEVO Spell Checker
- Join Date
- Sep 2014
- Location
- Florida
- Posts
- 3,198
- Downloads
- 1
- Uploads
- 0
-
23 June 2015, 10:32 #49WEVO Spell Checker
- Join Date
- Sep 2014
- Location
- Florida
- Posts
- 3,198
- Downloads
- 1
- Uploads
- 0
ok small update UV is not sending me the 16 barrel instead a 10.5
so now i need a new rail ?? i am looking at some 10inch rails and some .30cal muzzle breaks all so$300 and 10 Pastrami Sandwiches and a case of Diet Coke. ( UWone77)
-
23 June 2015, 20:15 #50
😎
Sent from my iPhone using TapatalkFacebook - Marty Callan
-
23 June 2015, 20:36 #51
-
24 June 2015, 09:24 #52WEVO Spell Checker
- Join Date
- Sep 2014
- Location
- Florida
- Posts
- 3,198
- Downloads
- 1
- Uploads
- 0
-
24 June 2015, 16:27 #53
I picked a MAMS for my next project, but it sounds like this is just as good and less expensive:
http://precisionarmament.com/product...-muzzle-brake/
-
24 June 2015, 16:33 #54WEVO Spell Checker
- Join Date
- Sep 2014
- Location
- Florida
- Posts
- 3,198
- Downloads
- 1
- Uploads
- 0
-
27 June 2015, 20:43 #55WEVO Spell Checker
- Join Date
- Sep 2014
- Location
- Florida
- Posts
- 3,198
- Downloads
- 1
- Uploads
- 0
OK guys I have an issue the 300 barrel dose not fit on the small slot on the upper resiver I was doing a Mike up to show you guys the progress of the upper boom. That happen. I will post a pick soon so I can get an advice
$300 and 10 Pastrami Sandwiches and a case of Diet Coke. ( UWone77)
-
27 June 2015, 20:58 #56WEVO Spell Checker
- Join Date
- Sep 2014
- Location
- Florida
- Posts
- 3,198
- Downloads
- 1
- Uploads
- 0
16 upper (1 of 1)-12 by Luis f, on Flickr
$300 and 10 Pastrami Sandwiches and a case of Diet Coke. ( UWone77)
-
27 June 2015, 23:07 #57
Hit it with a rubber mallet a couple of times.
-
28 June 2015, 03:30 #58
A little grease may help too. I put some 33mm aeroshell grease on every barrel extension once I install the barrel. Had one that did like this recently. Little grease and boom, in like Flynn.
-
28 June 2015, 05:49 #59
I've done the Aeroshel/mallet bit and it easily popped in. Better too snug than loose. Be sure to hand tight a muzzle device first. Pounding on the crown just feels wrong.
-
28 June 2015, 06:11 #60
Like UW said hitting it with a rubber mallet will work. But if you don't want to do that, your barrel extension is probably far enough in that tightening down a barrel nut will seat it the rest of the way down.