Results 226 to 240 of 1819
Thread: Handgun Picture thread
-
15 April 2012, 10:37 #226
-
15 April 2012, 14:13 #227Member
- Join Date
- Dec 2011
- Location
- Colorado
- Posts
- 222
- Downloads
- 0
- Uploads
- 0
Corn snake / red rat snake, I believe.
C. Smith
-
16 April 2012, 11:20 #228
Love that photo with the snake. Very original!
-
27 April 2012, 04:40 #229
Ruger SR1911. Seems pretty well made for a mass-produced pistol. Trigger averaged 6 lbs 3 ozs (ten pulls on Lyman digital). Finish is fairly uniform and the fitment of parts was good. Grips were "pretty" but not grippy. Pressed checkering with flat diamonds and a lot of urethane over them. Had to put on a set of VZ's for now. Slide to Frame fit was surprisingly tight. Barrel bushing was very snug but turns by hand. Think I'll keep it.
As delivered:
After the VZ Grips were added - and an Ed Brown Maxi-Well
NRA Benefactor Member
NRA Certified Instructor
"I won't be wronged, I won't be insulted, and I won't be laid a hand on."
John Wayne - "The Shootist"
-
24 May 2012, 05:40 #230
I just received my new Guncrafter Industries CCO. It was a custom build that someone backed out of and I had to jump on the opportunity. I'm a little unsure about the sights, 10-8 .140 U-notch rear and gold bead front but they may grow on me. I'm also planning on changing the trigger from the short to a long at some point. Grips will get swapped with Harrison Carry G10's made by VZ. It is a sexy little pistol!!! (Sorry for the crappy pics, I'm not photographer and all I have is an iPhone)
Hatter
Took a little hiatus... good to be back.
-
26 May 2012, 22:35 #231
Looks nice Hatter. Good find!
-
12 June 2012, 17:17 #232
There is no comparison to Stickman but WHAT THE HECK! Is everyone else here a professional photographer too =D
Gives me some great inspiration to take new photos of my rig and hardware.
-
20 June 2012, 14:32 #233
Received a Les Baer Commanche Monolith today from Crazy John at 1911 Heaven. Bead-blasted hard-chrome, nite sights, mag well, extended single-side safety, extended magazine release. The holster is a high-ride pancake made for me by Rocky at Pure Kustom. Excuse the dirty spots, I have not cleaned it. Just wiped the flats for pix, that left some stains on the serrations and checkering. Left the factory "goo" on the internals for break-in. Extremely hard to rack, suggested 400 to 500 rounds to slick it up.
Last edited by Jerry R; 20 June 2012 at 14:37.
NRA Benefactor Member
NRA Certified Instructor
"I won't be wronged, I won't be insulted, and I won't be laid a hand on."
John Wayne - "The Shootist"
-
21 June 2012, 06:28 #234
I've seen a few full dustcover 1911s over the past couple days. I don't own one, but seeing them has made me remember how much I like the look.
Triple Bravo
http://www.flickr.com/photos/triplebravo/
-
20 August 2012, 20:28 #235
Just added this FNH FNX-9 to my collection last week.
-
20 August 2012, 20:36 #236
My EDC gun. Ruger LCP w/ LG431, Houge Handall Grip and Pearce Extended Magazine Floor Plates.
-
20 August 2012, 20:37 #237
My Ruger SR9c
-
20 August 2012, 20:41 #238
My S&W M&P45 w/ TLR-3 & Trijicon Night Sights
-
16 September 2012, 00:18 #239
-
16 September 2012, 18:36 #240
Colt 1911 Pre-70's work done by Richard Heine.